How do you find the AMO length of a recurve bow?
› Bowstring Blog
What is draw length on a 60 inch recurve bow?
For example, a bow that’s 60 inches long will have peak performance at a draw length of 24 inches.
How long should a bow be for a 60 inch string?
ATA Specs say that a bow should be properly braced with a string that measures 3″ shorter than the bow. So if a bow is 60″ is should be braced properly with a string measuring 57″ under 100 lbs of tension after 20 seconds.
What is the draw length of a 62 recurve bow?
Most recurves commonly come in lengths of 58, 60, and 62 inches. The old rule was if you had a short draw length, less than 28 inches, you should shoot a 56 or 58-inch bow. For 28 to 29½-inch draw lengths, a 60-inch bow would perform best. For draw lengths over 29½ inches, a 62-inch bow would be the best choice.
How do you find the AMO length of a recurve bow?
› Bowstring Blog
How long should a bow be for a 60 inch string?
ATA Specs say that a bow should be properly braced with a string that measures 3″ shorter than the bow. So if a bow is 60″ is should be braced properly with a string measuring 57″ under 100 lbs of tension after 20 seconds.
How do you measure Amo string length?
What is this? You are going to take the tape and measure along the curve of the bow limbs from the string groove to string groove. This is going to be your string length. Another way is to measure your bow from tip to tip to find the AMO length and then subtract accordingly to the type of bow you are using.
What is AMO draw length?
AMO DRAW LENGTH STANDARD
Draw Iength is a specified distance, or the distance at the archer’s full draw, from the nocking point on the string to the pivot point of the bow grip (or the theoretical vertical projection of a tangency line to the pivot point parallel to the string) plus 1¾”.
How do I know what draw length I need?
First, find a measuring tape and someone to help you. Next, stand up straight and spread your arms out wide. Hold that position while your helper takes a measurement of your wingspan between the fingertips of your middle fingers. Finally, take that measurement and divide by 2.5 to determine your proper draw length.
Where is draw length measured on a recurve bow?
Starting from the index (inside groove of the arrow nock where the string nestles into), measure the length to the end of the arrow shaft (not the field point or broadhead).
What size string do I need for a 62 inch bow?
To achieve the correct brace height you will need to use a bowstring of the same AMO length. (Example: An AMO 62” bow requires an AMO 62” string). The actual length of your bowstring (depending on the material) will be 3.5”-5” shorter than its marked AMO length.
What is the best string for a recurve bow?
Most recurve archers use DynaFLIGHT 97, BCY 8125, or BCY-X – basically a durable string with very few fibers for increased arrow speed.
Do you twist a recurve bow string?
When re-twisting to achieve correct brace height, be sure to twist in the direction that tightens the center serving. You can determine this immediately on an un-tensioned string simply by grasping each end of the served area between thumb and forefinger, and twisting.
Does draw length matter recurve bows?
Unlike a compound, recurves and longbows don’t have set draw lengths. However, the bow-tech must still find your draw length because the bow’s length must match your draw length. If you have a long draw length, you’ll need a longer bow to better accommodate your draw length and feel comfortable.
How do I know if my draw length is too long?
The ideal draw length for you is the one that allows you to anchor in a comfortable position, with your bow arm elbow unlocked (slightly bent) and your release arm elbow and forearm pointing straight away from the target. If the release arm elbow points left or right, your draw length is too long or too short.
Is arrow length the same as draw length?
It’s quite common for archers to assume that draw length equals arrow length when shooting a compound bow. But it’s actually best to think of the two measurements as being related to each other but not married. Your draw length obviously will influence the length of your arrows.
What is AMO arrow length?
AMO Arrow Length is the measurement of an arrow taken from the bottom of the groove of the nock, to the end of the shaft. (Not including the points or point inserts).
What does Amo mean on a bow string?
AMO stands for the Archery Manufacturers Organization. It created a set of standards for things such as defining bow length. When people give a length of a bow in inches they almost always mean AMO bow length. AMO bow length is the length of the string plus 3 inches.
What does Amo mean for a bow?
The industry has a standardised method of measuring arrow length, and you will often see this referred to as AMO Length. AMO stands for Archery Manufacturers Organisation. This is the method where a measurement is taken between the groove of the nock and the front end of the shaft.
How do you determine arrow length?
The standard way to measure arrow length is from the back of the point to the throat of the nock. Your draw length and arrow spine will influence your arrow length. If you’re a 28-inch draw length and want an arrow that ends at the front of the riser, your arrow length would be around 27 inches.